①. 均速管流量計（例如阿牛巴、威力巴等）、畢托管流量計及其變形產品如V形畢托管流量計和畢托式文丘里管，宜安裝在水平管道上，當測量氣體或蒸汽時，也可安裝在垂直管道上。

 ②. 均速管流量計不可用于測量兩相流及工作溫度低于飽和溫度的蒸汽流量的測量。

 ③. 均速管流量計應安裝在被測介質完全充滿的管道上。

 ④. 均速管流量計在工藝管道上截面上的插入方位應滿足下列要求：在水平管道上安裝、測量氣體時，應在水平線以上且與水平線夾角30°～150°的范圍內；在水平管道上安裝、測量液體和蒸汽時，應在水平線以下且與水平線夾角-50°～-130°的范圍內；在垂直管道上安裝時，可在與管道中心線垂直的平面內的任意位置；均速管流量計測壓孔開孔中心線與管道中心線的偏差應小于3°，均速管流量計中心線與管線垂直度偏差應小于5°，與管道中心線的偏差應小于3°。

 ⑤. 測量精度要求為±1％時，均速管流量計上、下游側直管段長度應符合表2.46的要求。測量精度要求為士3％時，至少應有上游側3DN、下游側2DN的直管段長度。